View TSOP57236_5328227.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 1 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ir receiver modules for remote control systems features ? height of 0.8 mm ? 75 half angle sensitivity ? low supply current ? photo detectors and preamplifier in one package ? internal filter for pcm frequency ? supply voltage: 2.5 v to 5.5 v, typically even 2.0 v to 5.5 v is possible ? improved immunity against ambient light ? insensitive to supply voltage ripple and noise ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 description the tsop572.., tsop574.. series are miniaturized receiver modules for infrared remote control systems. a pin diode and a preamplifier are assembled on a lead frame, the epoxy lens cap is designed as an ir filter. the demodulated output signal can be directly decoded by a microprocessor. the tsop572.. is compatible with all common ir remote control data formats. the tsop574.. is optimized to suppress almost all spurious pulses from energy saving fluorescent la mps but will also suppress some data signals. this component has not been qualified according to automotive specifications. block diagram application circuit 22531-1 parts table carrier frequency standard applications (agc2) very noisy environments (agc4) 36 khz TSOP57236 tsop57436 38 khz tsop57238 tsop57438 40 khz tsop57240 tsop57440 56 khz tsop57256 tsop57456 33 k v s out demo- gnd pass agc input pin band dulator control circuit 4, 5 1 2, 3, 6, 7, 8 20445-6 c 1 ir receiver gnd circuit c r 1 + v s gnd transmitter with tsalxxxx v s v o 17170-10 out the external components r 1 and c 1 are optional to improve the robustness against electrical overstress (typical values are r 1 = 100 , c 1 = 0.1 f).
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 2 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? stresses beyond those listed under absolute maximum ratings ma y cause permanent damage to the device. this is a stress ratin g only and functional operation of the device at these or any other cond itions beyond those indicated in the operational sections of t his specification is not implied. exposure to absolute maximum rating co nditions for extended periods may affect the device reliability. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - output active low fig. 2 - puls e length and sensitivity in dark ambient absolute maximum ratings parameter test condition symbol value unit supply voltage v s - 0.3 to + 6 v supply current i s 5ma output voltage v o - 0.3 to (v s + 0.3) v output current i o 5ma junction temperature t j 100 c storage temperature range t stg - 25 to + 85 c operating temperature range t amb - 25 to + 85 c power consumption t amb 85 c p tot 10 mw electrical and optical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit supply voltage v s 2.5 5.5 v supply current v s = 5 v, e v = 0 i sd 0.55 0.7 0.9 ma e v = 40 klx, sunlight i sh 0.8 ma transmission distance e v = 0, ir diode tsal6200, i f = 250 ma, test signal see fig. 1 d40m output voltage low i osl = 0.5 ma, e e = 0.7 mw/m 2 , test signal see fig. 1 v osl 100 mv minimum irradiance pulse width tolerance: t pi - 5/f o < t po < t pi + 6/f o, test signal see fig. 1 e e min. 0.2 0.4 mw/m 2 maximum irradiance t pi - 5/f o < t po < t pi + 6/f o , test signal see fig. 1 e e max. 50 w/m 2 directivity angle of half transmission distance ? 1/2 75 deg e e t t pi * t * t pi 10/f 0 is recommended for optimal function v o v oh v ol t 16110 optical test signal (ir diode tsal6200, i f = 0.4 a, 30 pulses, f = f 0 , t = 10 ms) output signal t d 1) t po 2) 1) 7/f 0 < t d < 15/f 0 2) t pi - 5/f 0 < t po < t pi + 6/f 0 1.0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0.1 1 10 10 2 10 3 10 4 e e - irradiance (mw/m 2 ) t po - output pulse width (ms) input burst length output pulse width = 950 nm, optical test signal, fig.1 0 0.1
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 3 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 3 - output function fig. 4 - output pulse diagram fig. 5 - frequency depe ndance of responsivity fig. 6 - sensitivity in bright ambient fig. 7 - sensitivity vs. supply voltage disturbances fig. 8 - max. envelope duty cycle vs. burst length e e t v o v oh v ol t 600 s 600 s t = 60 ms t on t off 94 8134 optical t est signal output signal , (see fig. 4) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.1 1 10 10 2 10 3 10 4 10 5 e e - irradiance (mw/m 2 ) t on , t off - output pulse width (ms) = 950 nm, optical test signal, fig. 3 t off t on 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.7 0.9 1.1 1.3 f/f 0 - relative frequency 16925 f = f 0 5 % f(3 db) = f 0 /10 e /e - rel. responsivity e min. e 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0.01 0.1 1 10 100 e e - ambient dc irradiance (w/m 2 ) e e min. - threshold irradiance (mw/m 2 ) correlation with ambient light sources: 10 w/m 2 = 1.4 klx (std. illum. a, t = 2855 k) 10 w/m 2 = 8.2 klx (daylight, t = 5900 k) wavelength of ambient illumination: = 950 nm 4.5 5.0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1 10 100 1000 v s rms - ac voltage on dc supply voltage (mv) e e min. - threshold irradiance (mw/m 2 ) f = f 0 f = 20 khz f = 30 khz f = 100 hz f = 10 khz 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 20 40 60 80 100 120 burst length (number of cycles/burst) max. envelope duty cycle f = 38 khz, e e = 2 mw/m 2 tsop572.. tsop574.. 21396_15
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 4 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 9 - sensitivity vs. ambient temperature fig. 10 - relative spectral sensitivity vs. wavelength fig. 11 - horizontal directivity fig. 12 - sensitivity vs. supply voltage t amb - ambient temperature (c) e e min. - sensitivity (mw/m 2 ) 0 0.05 0.10 0.15 0.20 0.40 - 30 - 10 10 30 50 70 90 0.30 0.25 0.35 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 750 800 850 900 950 1000 1050 1150 - wavelength (nm) s( ) rel - relative spectral sensitivity 1100 0.1 0.3 0.5 0.7 0.9 80 70 60 50 40 30 20 10 0 - 10 - 20 - 30 - 40 - 50 - 60 - 70 - 80 21947 0 0.1 0.2 0.3 0.4 0.5 0.8 1.5 2.5 3.5 4.5 5.5 2.0 3.0 4.0 5.0 v s - supply voltage (v) e e min. - sensitivity (mw/m 2 ) 0.6 0.7
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 5 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 suitable data format the tsop572.., tsop574.. series is designed to suppress spurious output pulses due to noise or disturbance signals. data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. the data signal should be close to the band-pass center frequency (e.g. 38 khz) and fulfill the conditions in the table below. when a data signal is applied to the tsop572.., tsop574.. in the presence of a disturbance signal, th e sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. some examples of disturbance signals which are suppressed are: ? dc light (e.g. from tungsten bulb or sunlight) ? continuous signals at any frequency ? strongly or weakly modulated noise from fluorescent lamps with electronic ballasts (s ee figure 12 or figure 13) fig. 13 - ir signal from fluorescent lamp with low modulation fig. 14 - ir signal from fluorescent lamp with high modulation note ? for data formats with short bursts please see the data sheet for tsop573.. 0101520 time (ms) 16920 ir signal 5 0101520 time (ms) 16921 ir signal 5 tsop572.. tsop574.. minimum burst length 10 cycl es/burst 10 cycles/burst after each burst of length a minimum gap time is required of 10 to 70 cycles 10 cycles 10 to 42 cycles 10 cycles for bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 42 cycles > 10 x burst length maximum number of continuous short bursts/second 800 1300 recommended for nec code yes yes recommended for rc5/rc6 code yes yes recommended for sony code yes no recommended for thom son 56 khz code yes yes recommended for mitsubishi code (38 khz, prebur st 8 ms, 16 bit) yes yes recommended for rcmm code no no suppression of interference from fluorescent lamps most common disturbance signals are suppressed even extreme disturbance signals are suppressed
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 6 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters note (1) optically effective area 0.8 0.15 3.95 3.95 (2.75) (1) 0.55 (0.95) 0.55 (1.8) pinning from topview g nd g nd out v s (v s ) ( g nd) ( g nd) ( g nd) 0.75 0.05 4 x 0.75 = 3 0.35 0.05 (8 x) 1.5 3 (0.3) (0.3) (0.3) (0.7) (1.9) (1) (3.4) (1) marking area propo s ed pad layout from component s ide (dim. for reference only) (3.95) (3.95) (0.35) (4 x) (0.8) (4 x) (2.75) (3) 0.475 (0.4) pin 1 identification pin 1 identification technical drawing s according to din s pecification s not indicated tolerance s 0.1 drawing-no.: 6.550-5315.01-4 i ss ue: 1; 14.11.11 12 3 45 6 7 8
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 7 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 assembly instructions reflow soldering ? reflow soldering must be done within 168 h while stored under a max. temperature of 30 c, 60 % rh after opening the dry pack envelope ? set the furnace temperatures for pre-heating and heating in accordance with the refl ow temperature profile as shown in the diagram. excercise extreme care to keep the maximum temperatu re below 260 c. the temperature shown in the profile means the temperature at the device surface. since there is a temperature difference between the component and the circuit bo ard, it should be verified that the temperature of the device is accurately being measured ? handling after reflow should be done only after the work surface has been cooled off manual soldering ? use a soldering iron of 25 w or less. adjust the temperature of the soldering iron below 300 c ? finish soldering within 3 s ? handle products only after th e temperature has cooled off vishay lead (pb)-free reflow solder profile note (1) moq: minimum order quantity ordering information ordering code packaging volume (1) remarks tsop57..tt1 tape and reel moq: 1800 pcs 3.95 mm x 3.95 mm x 0.75 mm tsop57..tt2 moq: 7000 pcs 0 50 100 150 200 250 300 0 50 100 150 200 250 300 t (s) t (c) 255 c 240 c 245 c max. 260 c max. 120 s max. 100 s 217 c max. 20 s max. ramp up 3 c/s max. ramp down 6 c/s max. 2 cycles allowed 19800
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 8 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop57... dimensions in millimeters leader and trailer tape: part s mounted empty trailer 200 mm min. empty leader 400 mm min. direction of pulling out unreel direction ? 60 min. ? y 2 0.5 label po s ted here coming out from reel tape po s ition (12.4) 18.4 max. ? 13 0.2 ? 21 0.8 100 mm min. with cover tape x 2:1 tape and reel dimen s ion s : (2) (1.75) (5.5) 12 0.3 (8) (4) (? 1.5) (0.3) reel s ize "y" tt1 ? 180 2 = 1800 pc s . tt2 ? 330 2 = 7000 pc s . (1.2) technical drawing s according to din s pecification s not indicated tolerance s 0.1 drawing-no.: 9.700-5347.01-4 i ss ue: 1; 14.11.11
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 9 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 label standard bar code labels for finished goods the standard bar code labels are product labels and used for identification of goods. th e finished goods are packed in final packing area. the standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. the labels are on each packing unit and contain vishay semiconductor gmbh specific data. dry packing the reel is packed in an an ti-humidity bag to protect the devices from absorbing moisture during transportation and storage. final packing the sealed reel is packed into a cardboard box. a secondary cardboard box is used for shipping purposes. recommended method of storage dry box storage is recommended as soon as the aluminum bag has been opened to prev ent moisture absorption. the following conditions should be observed, if dry boxes are not available: ? storage temperature 10 c to 30 c ? storage humidity 60 % rh max. after more than 168 h under these conditions moisture content will be too high for reflow soldering. in case of moisture absorption , the devices will recover to the former condition by drying under the following condition: 192 h at 40 c + 5 c/- 0 c and < 5 % rh (dry air/nitrogen) or 96 h at 60 c + 5 c and < 5 % rh for all device containers or 24 h at 125 c + 5 c not suitable for reel or tubes. an eia jedec standard jstd-0 20 level 3 label is included on all dry bags. vishay semiconductor gmbh standard bar code product label (finished goods) plain writing abbreviation length item-description -18 item-n u m b er ino 8 selection-code sel 3 lot-/serial-n u m b er batch 10 data-code cod 3 (yww) plant-code ptc 2 q u antity qty 8 accepted b y acc - packed b y pck - mixed code indicator mixed code - origin xxxxxxx+ company logo long bar code top type length item-n u m b er n8 plant-code n2 se qu ence-n u m b er x3 q u antity n8 total length -21 short bar code bottom type length selection-code x3 data-code n3 batch-n u m b er x10 filter -1 total length -17 aluminum bag label reel 15973
tsop572.., tsop574.. www.vishay.com vishay semiconductors rev. 1.5, 20-jun-12 10 document number: 82434 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 eia jedec standard jstd-020 level 3 label is included on all dry bags esd precaution proper storage and handling procedures should be followed to prevent esd damage to the devices especially when they are removed from the antistatic shielding bag. electro-static sensitive devices warning labels are on the packaging. vishay semiconductors standard bar code labels the vishay semiconductors standard bar code labels are printed at final packing areas. the labels are on each packing unit and contain vishay semiconductors specific data. bar code product label (example) 1. calculated shelf life in sealed bag: 12 months at <40c and <90% relative humidity (rh) 3. after bag is opened, devices that will be subjected to reflow solder or other high temperature process must be 4. devices require bake, before mounting, if: a) humidity indicator card reads > 10% for level 2a - 5a devices or >60% for level 2 devices when read at 235c b) 3a or 3b are not met 5. if baking is required, refer to ipc/jedec j-std-033 for bake procedure 2. peak package body temperature:_______________________c if blank, see adjacent bar code label a) mounted within:___________________hours of factory conditions 30c/60% rh, or b) stored per j-std-033 if blank, see adjacent bar code label bag seal date:_________________________________________ if blank, see adjacent bar code label note: level and body temperature defined by ipc/jedec j-std-020 this bag contains moisture-sensitive devices caution if blank, see adjacent bar code label 3 level 260 168 22650 22178
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu.

▲Up To Search▲

Price & Availability of TSOP57236

	To Download TSOP57236 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .